Skip to content
Loading map…

Fox and Fiddle

112 Spencer Ave North Bay ON P1B 7K6 · Restaurant

Official record from North Bay Parry Sound →

Inspection summary

Fox and Fiddle has been inspected 14 times by North Bay Parry Sound District Health Unit since April 18, 2024. The most recent inspection, on June 23, 2026, recorded 2 infractions.

None of the 14 inspections on record were free of infractions. In the past 12 months there were 7 inspections with 29 infractions recorded. The higher-risk findings here relate to: Food temperature control, Protecting food from contamination and Chemicals and toxic substances.

The number of infractions per inspection has stayed roughly the same over time.

What these findings mean

Health authorities word their violations differently, so we group them by what they mean for food safety. Higher-risk findings are the ones inspectors treat as critical, because they can directly make someone sick.

  • Food temperature controlHigher risk

    Bacteria multiply fastest between about 4 °C and 60 °C (40 °F to 140 °F). Inspectors check that cold food stays cold, hot food stays hot, cooked food is cooled quickly, and that staff have accurate thermometers. Temperature problems are one of the most common causes of food poisoning, so these are treated as critical findings.

    Recorded 11 times across 8 separate inspections, most recently on June 22, 2026. For example: Thermometers used to verify food preparation and storage temperatures

  • Protecting food from contaminationHigher risk

    This covers how food is stored, prepared and displayed: raw meat kept away from ready-to-eat food, food covered and stored off the floor, and nothing dripping or splashing into it. Cross-contamination from raw to cooked food is a direct route for salmonella and E. coli.

    Recorded 9 times across 9 separate inspections, most recently on June 22, 2026. For example: Food protected from potential contamination and/or adulteration

  • Chemicals and toxic substancesHigher risk

    Cleaning products, sanitizers and pesticides must be labelled and stored away from food and food-contact surfaces. Inspectors flag chemicals that could end up in food, as well as pest treatments applied without proper supervision.

    Recorded 7 times across 7 separate inspections, most recently on June 22, 2026. For example: Food contact surfaces properly designed, constructed, installed, maintained, located (smooth, non-absorbent, cleanable, corrosion resistant and non-toxic)

  • Cleaning and sanitizingHigher risk

    Anything that touches food, such as cutting boards, dishes and utensils, must be washed, rinsed and sanitized. Inspectors check dishwasher temperatures, sanitizer strength and how wiping cloths are stored. Poor sanitizing lets bacteria survive from one use to the next.

    Recorded 4 times across 4 separate inspections, most recently on February 11, 2026. For example: Food contact surfaces washed / rinsed / sanitized after each use and following any operations when contamination may have occurred

  • PestsHigher risk

    Signs of mice, rats, cockroaches or flies, or gaps and clutter that let them get in or hide. Pests carry bacteria and can contaminate food and surfaces, so evidence of activity is treated seriously and usually triggers a follow-up visit.

    Recorded 2 times across 2 separate inspections, most recently on February 24, 2026. For example: Adequate protection against the entrance of insects, vermin, and rodents

About this data

These results come from North Bay Parry Sound District Health Unit, which inspects food premises and other public facilities in this area. We republish the authority's public disclosure data and refresh it regularly; the official record is the final word.

14 inspections

  1. Re-inspection

    2 infractions

    • Walls clean and in good repair
      • * Fail to ensure walls of food premise kept clean and in good repair
    • Ceilings clean and in good repair
  2. Compliance (Required)

    5 infractions

    • Food protected from potential contamination and/or adulteration
      • * Fail to protect food from contamination and/or adulteration
      • Operator to ensure all food is properly stored, displayed, transported and served to prevent contamination
    • Proper storage of single-service containers/articles (utensils)
      • * Fail to store single-service containers and article (utensils) in a manner preventing contamination
      • Operator to ensure single-service containers/articles are protected and stored in a manner to prevent contamination
    • Food contact surfaces properly designed, constructed, installed, maintained, located (smooth, non-absorbent, cleanable, corrosion resistant and non-toxic)
      • * Fail to use equipment/utensils/dishes/food containers/multi-service articles in good repair (i.e. free from cracks/crevices/chips/open seams)
      • Operator to ensure all food contact surfaces/equipment/utensils/multi-service articles are made of materials that can be readily cleaned and sanitized
    • Ceilings clean and in good repair
      • * Fail to ensure ceiling of food premise kept clean and in good repair
      • Operator to ensure ceiling of the food premise is maintained in a sanitary condition and in good repair
    • Thermometers used to verify food preparation and storage temperatures
      • * Fail to provide thermometer in temperature controlled room / equipment used to store potentially hazardous foods
      • * Fail to use accurate thermometer to check storage temperature of potentially hazardous food
      • Operator to provide accurate and easily readable indicating thermometers in temperature controlled rooms/equipment used for storage of potentially hazardous foods
  3. Re-inspection

    4 infractions

    • Walls clean and in good repair
      • * Fail to ensure walls of food premise kept clean and in good repair
      • Operator to ensure walls of food premise are maintained in a sanitary condition and in good repair
    • Food protected from potential contamination and/or adulteration
      • * Observed raw foods stored above cooked / ready-to-eat foods
      • Operator to ensure cooked and ready-to-eat foods are separated and above raw foods when handled or stored
    • Adequate protection against the entrance of insects, vermin, and rodents
      • * Evidence of pests observed
      • Operator to ensure food premise shall be protected against the entry of pest
    • Equipment, non-food contact surfaces and linen are maintained, designed, constructed, installed and accessible for cleaning
      • * Fail to maintain all equipment/non-food contact surfaces are in clean and in good repair
      • Operator to ensure that all equipment/non-food contact surfaces are maintained clean and in good repair
      • Operator to ensure light fixtures are properly covered
  4. Re-inspection

    4 infractions

    • Equipment, non-food contact surfaces and linen are maintained, designed, constructed, installed and accessible for cleaning
      • * Fail to maintain all equipment/non-food contact surfaces are in clean and in good repair
      • Operator to ensure light fixtures are properly covered
    • Food contact surfaces properly designed, constructed, installed, maintained, located (smooth, non-absorbent, cleanable, corrosion resistant and non-toxic)
      • * Fail to use equipment/utensils/dishes/food containers/multi-service articles that are corrosion resistant/non-toxic/non-absorbent
      • Operator to ensure all food contact surfaces/equipment/utensils/multi-service articles are made of materials that are corrosion resistant/non-toxic/non-absorbent
    • Ceilings clean and in good repair
      • * Fail to ensure ceiling of food premise kept clean and in good repair
      • Operator to ensure ceiling of the food premise is maintained in a sanitary condition and in good repair
    • Walls clean and in good repair
      • * Fail to ensure walls of food premise kept clean and in good repair
      • Operator to ensure walls of food premise are maintained in a sanitary condition and in good repair
  5. Compliance (Required)

    7 infractions

    • Minimum of 1 Certified Food Handler per hour of operation?
      • * Fail to provide proof of a certified food handler certificate
      • Operator to provide proof of a certified food handler certificate
    • Walls clean and in good repair
      • * Fail to ensure walls of food premise kept clean and in good repair
      • Operator to ensure walls of food premise are maintained in a sanitary condition and in good repair
    • General housekeeping is satisfactory
      • * Fail to remove all materials not associated with the daily operation of the food premise
      • * Fail to arrange furniture, equipment and appliances as to permit thorough cleaning and the maintaining of the room or place in a clean and sanitary condition
      • Operator to remove all materials not associated with the daily operation of food premise
      • Operator to ensure the furniture, equipment and appliances are arranged to permit thorough cleaning and the maintaining of the room or place in a clean and sanitary condition
    • Ceilings clean and in good repair
      • * Fail to ensure ceiling of food premise kept clean and in good repair
      • Operator to ensure ceiling of the food premise is maintained in a sanitary condition and in good repair
    • Food contact surfaces washed / rinsed / sanitized after each use and following any operations when contamination may have occurred
      • * Fail to ensure food contact surfaces are cleaned & sanitized after each use or as often as necessary
      • Operator to ensure all food contact surfaces are properly cleaned & sanitized
    • Food protected from potential contamination and/or adulteration
      • * Fail to protect food from contamination and/or adulteration
      • * Observed scoops/utensils not being stored in a sanitary manner to prevent contamination and/or adulteration
      • Operator to ensure all food is properly stored, displayed, transported and served to prevent contamination
    • Adequate protection against the entrance of insects, vermin, and rodents
      • * Evidence of pests observed
      • Operator to ensure food premise shall be protected against the entry of pest
      • Provide proof of contract with licensed pest control operator to control and remove insect/pest infestation
  6. Re-inspection

    1 infraction

    • Food protected from potential contamination and/or adulteration
  7. Compliance (Required)

    6 infractions

    • Food protected from potential contamination and/or adulteration
      • * Observed scoops/utensils not being stored in a sanitary manner to prevent contamination and/or adulteration
      • Operator to ensure scoops/utensils are stored and maintained in a sanitary manner to prevent contamination and/or adulteration
    • Mechanical dishwashing: Wash / rinse water clean, water temperature, timing cycles, sanitizer
      • * Fail to ensure adequate sanitizer concentration are achieved for sanitizing
      • Chlorine sanitizer concentration must be at least 100 parts per million at 24°C or greater for at least 45 seconds
      • Quaternary ammonium compound must be at least 200 parts per million at 24°C or greater for at least 45 seconds
      • Operator to provide an appropriate test reagent to verify the concentration of the sanitizer
    • Food contact surfaces washed / rinsed / sanitized after each use and following any operations when contamination may have occurred
    • Walls clean and in good repair
      • * Fail to ensure walls of food premise kept clean and in good repair
      • Operator to ensure walls of food premise are maintained in a sanitary condition and in good repair
    • Food contact surfaces properly designed, constructed, installed, maintained, located (smooth, non-absorbent, cleanable, corrosion resistant and non-toxic)
      • * Fail to provide utensils and/or multi-service food containers/multi-service articles that can be readily cleaned and sanitized
      • Operator to ensure all food contact surfaces/equipment/utensils/multi-service articles are made of materials that can be readily cleaned and sanitized
    • Proper storage of single-service containers/articles (utensils)
      • * Fail to store single-service containers and article (utensils) in a manner preventing contamination
      • Operator to ensure single-service containers/articles are protected and stored in a manner to prevent contamination
  8. Complaint & Compliance

    3 infractions

    • Food contact surfaces washed / rinsed / sanitized after each use and following any operations when contamination may have occurred
      • * Fail to ensure sanitizing solution contains the appropriate type of chemical solution and/or concentration/strength of sanitizer
      • Operator to ensure sanitizing solution contain the appropriate type of chemical solution and/or concentration/strength for sanitizing
    • Potentially hazardous food is held at 4°C (40°F) or lower
    • Food protected from potential contamination and/or adulteration
  9. Compliance (Required)

    7 infractions

    • Food protected from potential contamination and/or adulteration
    • Thermometers used to verify food preparation and storage temperatures
      • * Fail to provide thermometer in temperature controlled room / equipment used to store potentially hazardous foods
      • Operator to provide accurate and easily readable indicating thermometers in temperature controlled rooms/equipment used for storage of potentially hazardous foods
    • Floors clean and in good repair
      • * Fail to ensure floors of food premise are kept clean and/or in good repair
    • Equipment, non-food contact surfaces and linen are maintained, designed, constructed, installed and accessible for cleaning
    • Food contact surfaces properly designed, constructed, installed, maintained, located (smooth, non-absorbent, cleanable, corrosion resistant and non-toxic)
      • * Fail to maintain utensils, multi-service articles and/or food contact surfaces in a clean and sanitary manner and/or in good repair
      • Operator to ensure all food contact surfaces, utensils and/or multi-service articles are cleaned and sanitized after each use and are maintained in good repair
    • Mechanical dishwashing: Wash / rinse water clean, water temperature, timing cycles, sanitizer
    • Hand washing basin with supplies of hot and cold water, soap in a dispenser and single-use towels
  10. Compliance (Required)

    4 infractions

    • Washing hands thoroughly before and after handling food
      • * Food handlers fail to wash hands as often as necessary to prevent the contamination of food or food areas
      • Food handlers must wash hands after they are contaminated and before handling food
    • Food contact surfaces properly designed, constructed, installed, maintained, located (smooth, non-absorbent, cleanable, corrosion resistant and non-toxic)
      • * Fail to use equipment/utensils/dishes/food containers/multi-service articles in good repair (i.e. free from cracks/crevices/chips/open seams)
      • Operator to ensure all food contact surfaces/equipment/utensils/multi-service articles are made of materials that can be readily cleaned and sanitized
    • Potentially hazardous food is held at 4°C (40°F) or lower
    • Food protected from potential contamination and/or adulteration
      • * Fail to protect food from contamination and/or adulteration
      • Operator to ensure all food is properly stored, displayed, transported and served to prevent contamination
      • Operator to ensure all foods are stored off the floor
  11. Re-inspection

    3 infractions

    • Potentially hazardous food is held at 4°C (40°F) or lower
      • * Fail to ensure potentially hazardous foods are held at 4°C (40°F) or less
      • CCP monitoring should be conducted by operator
      • Potentially hazardous foods observed at an internal temperature above 4° C (40°F)
      • Operator to ensure potentially hazardous foods are held at 4°C (40°F) or lower
    • Equipment, non-food contact surfaces and linen are maintained, designed, constructed, installed and accessible for cleaning
      • * Fail to maintain all equipment/non-food contact surfaces are in clean and in good repair
      • Operator to adjust or repair the malfunctioning cooler immediately. Do not store any potentially hazardous foods in the malfunctioning unit until it is able to maintain hazardous foods at 4° C or lower
    • Food contact surfaces properly designed, constructed, installed, maintained, located (smooth, non-absorbent, cleanable, corrosion resistant and non-toxic)
      • * Fail to use equipment/utensils/dishes/food containers/multi-service articles in good repair (i.e. free from cracks/crevices/chips/open seams)
      • Operator to ensure all food contact surfaces, utensils and/or multi-service articles are cleaned and sanitized after each use and are maintained in good repair
  12. Compliance (Required)

    8 infractions

    • Mechanical dishwashing: Wash / rinse water clean, water temperature, timing cycles, sanitizer
      • * Fail to ensure adequate sanitizer concentration are achieved for sanitizing
      • Chlorine sanitizer concentration must be at least 100 parts per million at 24°C or greater for at least 45 seconds
      • Quaternary ammonium compound must be at least 200 parts per million at 24°C or greater for at least 45 seconds
      • Iodine concentration must be at least 25 parts per million at 24°C or greater for at least 45 seconds
      • Operator to provide an appropriate test reagent to verify the concentration of the sanitizer
    • Floors clean and in good repair
      • * Fail to ensure floors of food premise are kept clean and/or in good repair
      • Operator to ensure floors are kept clean and in good repair
      • Operator to ensure floors are maintained from clutter to permit adequate cleaning
    • Food protected from potential contamination and/or adulteration
      • * Fail to protect food from contamination and/or adulteration
      • Operator to ensure all food is properly stored, displayed, transported and served to prevent contamination
    • Washing hands thoroughly before and after handling food
      • * Food handlers fail to wash hands as often as necessary to prevent the contamination of food or food areas
      • Food handlers must wash hands after they are contaminated and before handling food
    • Potentially hazardous food is held at 4°C (40°F) or lower
      • * Fail to ensure potentially hazardous foods are held at 4°C (40°F) or less
      • Operator to ensure potentially hazardous foods are held at 4°C (40°F) or lower
    • Food contact surfaces properly designed, constructed, installed, maintained, located (smooth, non-absorbent, cleanable, corrosion resistant and non-toxic)
      • * Fail to use equipment/utensils/dishes/food containers/multi-service articles in good repair (i.e. free from cracks/crevices/chips/open seams)
      • Operator to ensure all food contact surfaces/equipment/utensils/multi-service articles are made of materials that can be readily cleaned and sanitized
    • Equipment, non-food contact surfaces and linen are maintained, designed, constructed, installed and accessible for cleaning
      • * Fail to maintain all equipment/non-food contact surfaces are in clean and in good repair
      • * Fail to maintain all equipment/non-food contact surfaces are of sound and tight construction
      • Operator to ensure that all equipment/non-food contact surfaces are maintained clean and in good repair
      • Operator to ensure that all equipment/non-food contact surfaces are readily cleanable/non-absorbent and of sound and tight construction.
    • Thermometers used to verify food preparation and storage temperatures
      • * Fail to provide easily readable thermometer
      • Operator to provide accurate and easily readable indicating thermometers in temperature controlled rooms/equipment used for storage of potentially hazardous foods
  13. Re-inspection

    1 infraction

    • Walls clean and in good repair
      • * Fail to ensure walls of food premise kept clean and in good repair
      • Operator to ensure walls of food premise are maintained in a sanitary condition and in good repair
  14. Compliance (Required)

    4 infractions

    • Walls clean and in good repair
      • * Fail to ensure walls of food premise kept clean and in good repair
      • Operator to ensure walls of food premise are maintained in a sanitary condition and in good repair
    • Floors clean and in good repair
      • * Fail to ensure floor of food-handling room kept clean and in good repair
      • Operator to ensure floors are kept clean and in good repair
    • Food contact surfaces washed / rinsed / sanitized after each use and following any operations when contamination may have occurred
      • * Fail to ensure food contact surfaces are cleaned & sanitized after each use or as often as necessary
      • * Fail to ensure sanitizing solution contains the appropriate type of chemical solution and/or concentration/strength of sanitizer
      • Operator to ensure all food contact surfaces are properly cleaned & sanitized
      • Operator to ensure sanitizing solution contain the appropriate type of chemical solution and/or concentration/strength for sanitizing
    • Potentially hazardous food is held at 4°C (40°F) or lower
      • * Fail to ensure potentially hazardous foods are held at 4°C (40°F) or less
      • Potentially hazardous foods observed at an internal temperature above 4° C (40°F)
      • Operator to conduct internal temperature checks of potentially hazardous foods

Nearby inspected facilities

Own this business? Add a badge to your website