Skip to content
Loading map…

Mexitaco

74 Simcoe St N, Oshawa ON L1G 4S2 · Food Safety Inspections

8 inspections

  1. Routine

    3 infractions

    • Food protected from potential contamination and/or adulteration
      • * Observed potentially hazardous food not covered to prevent contamination / adulteration
      • Operator to ensure all foods are covered in storage
    • Food contact surfaces properly designed, constructed, installed, maintained, located (smooth, non-absorbent, cleanable, corrosion resistant and non-toxic)
      • * Fail to maintain utensils, multi-service articles and/or food contact surfaces in a clean and sanitary manner and/or in good repair
      • Operator to ensure all food contact surfaces, utensils and/or multi-service articles are cleaned and sanitized after each use and are maintained in good repair
    • Equipment, non-food contact surfaces and linen are maintained, designed, constructed, installed and accessible for cleaning
      • * Fail to maintain all equipment/non-food contact surfaces are in clean and in good repair
      • Operator to ensure that all equipment/non-food contact surfaces are maintained clean and in good repair
  2. Re-Inspection

    0 infractions

  3. Routine

    2 infractions

    • Food protected from potential contamination and/or adulteration
      • * Observed potentially hazardous food not covered to prevent contamination / adulteration
      • * Observed raw foods stored above cooked / ready-to-eat foods
      • Operator to ensure cooked and ready-to-eat foods are separated and above raw foods when handled or stored
      • Operator to ensure all foods are covered in storage
    • Mechanical dishwashing: Wash / rinse water clean, water temperature, timing cycles, sanitizer
      • * Fail to ensure adequate sanitizer concentration are achieved for sanitizing
      • Chlorine sanitizer concentration must be at least 100 parts per million at 24°C or greater for at least 45 seconds
      • Operator to ensure utensils are manually sanitized after each mechanical wash cycle
  4. Routine

    2 infractions

    • Hot holding of potentially hazardous food: minimum of 60°C (140°F) after cooking / rapid re-heating
      • * Fail to hold potentially hazardous food at 60°C (140°F) or higher after cooking / rapid re-heating
      • Operator to ensure potentially hazardous foods are held at 60°C (140°F) or higher after cooking/rapid reheating
    • Separate hand washing basin provided for food handlers
      • * Fail to use basin only for hand washing of employees
      • Operator to ensure designated hand washing basin is only used for hand washing
  5. Re-Inspection

    0 infractions

  6. Re-Inspection

    2 infractions

    • Constant supply of hot and cold running water under pressure
      • * Fail to provide premise with hot and/or cold water
      • Operator to ensure hot and cold running water under pressure is provided
    • The premises is maintained free from every SERIOUS condition that may be a health hazard, adversely affecting the sanitary operation of the premises or adversely affecting the wholesomeness of the food
      • Fail to provide premise with hot and/or cold water under pressure
      • Operator to operate and maintain premise free from every condition that may be a health hazard
  7. Routine

    3 infractions

    • Thermometers used to verify food preparation and storage temperatures
      • * Fail to provide thermometer in temperature controlled room / equipment used to store potentially hazardous foods
      • Operator to provide accurate and easily readable indicating thermometers in temperature controlled rooms/equipment used for storage of potentially hazardous foods
    • Mechanical dishwashing: Wash / rinse water clean, water temperature, timing cycles, sanitizer
      • * Fail to ensure adequate sanitizer concentration are achieved for sanitizing
      • Chlorine sanitizer concentration must be at least 100 parts per million at 24°C or greater for at least 45 seconds
      • Operator to ensure utensils are manually sanitized after each mechanical wash cycle
    • Food contact surfaces washed / rinsed / sanitized after each use and following any operations when contamination may have occurred
      • * Fail to ensure food contact surfaces are cleaned & sanitized after each use or as often as necessary
      • * Fail to ensure sanitizing solution contains the appropriate type of chemical solution and/or concentration/strength of sanitizer
      • Operator to ensure all food contact surfaces are properly cleaned & sanitized
      • Operator to ensure sanitizing solution contain the appropriate type of chemical solution and/or concentration/strength for sanitizing
  8. Routine

    3 infractions

    • Thermometers used to verify food preparation and storage temperatures
      • * Fail to provide thermometer in temperature controlled room / equipment used to store potentially hazardous foods
      • Operator to provide accurate and easily readable indicating thermometers in temperature controlled rooms/equipment used for storage of potentially hazardous foods
    • Washing hands thoroughly before and after handling food
      • * Food handlers fail to wash hands as often as necessary to prevent the contamination of food or food areas
      • Food handlers must wash hands after they are contaminated and before handling food
      • Operator to wash hands before putting on disposable gloves
    • Food protected from potential contamination and/or adulteration
      • * Observed scoops/utensils not being stored in a sanitary manner to prevent contamination and/or adulteration
      • Operator to ensure scoops/utensils are stored and maintained in a sanitary manner to prevent contamination and/or adulteration