Skip to content
Loading map…

Pelican Events & Catering

804 Ritson Rd S, Oshawa ON L1H 5L4 · Food Safety Inspections

Official record from Durham Region →

Inspection summary

Pelican Events & Catering has been inspected 11 times by Durham Region Health Department since December 4, 2024. The most recent inspection, on September 3, 2026, recorded 1 infraction.

None of the 11 inspections on record were free of infractions. In the past 12 months there were 7 inspections with 33 infractions recorded. The higher-risk findings here relate to: Pests, Protecting food from contamination and Food temperature control.

Recent inspections have recorded more infractions than earlier ones, so it is worth reading the latest reports closely.

What these findings mean

Health authorities word their violations differently, so we group them by what they mean for food safety. Higher-risk findings are the ones inspectors treat as critical, because they can directly make someone sick.

  • PestsHigher risk

    Signs of mice, rats, cockroaches or flies, or gaps and clutter that let them get in or hide. Pests carry bacteria and can contaminate food and surfaces, so evidence of activity is treated seriously and usually triggers a follow-up visit.

    Recorded 9 times across 8 separate inspections, most recently on September 3, 2026. For example: Adequate protection against the entrance of insects, vermin, and rodents

  • Protecting food from contaminationHigher risk

    This covers how food is stored, prepared and displayed: raw meat kept away from ready-to-eat food, food covered and stored off the floor, and nothing dripping or splashing into it. Cross-contamination from raw to cooked food is a direct route for salmonella and E. coli.

    Recorded 6 times across 6 separate inspections, most recently on August 19, 2026. For example: Food protected from potential contamination and/or adulteration

  • Food temperature controlHigher risk

    Bacteria multiply fastest between about 4 °C and 60 °C (40 °F to 140 °F). Inspectors check that cold food stays cold, hot food stays hot, cooked food is cooled quickly, and that staff have accurate thermometers. Temperature problems are one of the most common causes of food poisoning, so these are treated as critical findings.

    Recorded 3 times across 3 separate inspections, most recently on February 24, 2026. For example: Mechanical dishwashing: Wash / rinse water clean, water temperature, timing cycles, sanitizer

  • Cleaning and sanitizingHigher risk

    Anything that touches food, such as cutting boards, dishes and utensils, must be washed, rinsed and sanitized. Inspectors check dishwasher temperatures, sanitizer strength and how wiping cloths are stored. Poor sanitizing lets bacteria survive from one use to the next.

    Recorded 3 times across 2 separate inspections, most recently on February 24, 2026. For example: Manual dishwashing: Wash, rinse, sanitize technique

  • Chemicals and toxic substancesHigher risk

    Cleaning products, sanitizers and pesticides must be labelled and stored away from food and food-contact surfaces. Inspectors flag chemicals that could end up in food, as well as pest treatments applied without proper supervision.

    Recorded 2 times across 2 separate inspections, most recently on August 19, 2026. For example: Food contact surfaces properly designed, constructed, installed, maintained, located (smooth, non-absorbent, cleanable, corrosion resistant and non-toxic)

About this data

These results come from Durham Region Health Department, which inspects food premises and other public facilities in this area. We republish the authority's public disclosure data and refresh it regularly; the official record is the final word.

11 inspections

  1. Re-Inspection

    1 infraction

    • Adequate protection against the entrance of insects, vermin, and rodents
      • * Fail to prevent the entrance of insect / rodent / pest
      • Operator to ensure storage areas are maintained clean and organized to facilitate the monitoring of pest control
      • Operator to ensure food premise shall be protected against the entry of pest
  2. Re-Inspection

    3 infractions

    • Equipment, non-food contact surfaces and linen are maintained, designed, constructed, installed and accessible for cleaning
      • * Fail to maintain all equipment/non-food contact surfaces are in clean and in good repair
      • Operator to ensure that all equipment/non-food contact surfaces are maintained clean and in good repair
    • Adequate protection against the entrance of insects, vermin, and rodents
      • * Evidence of pests observed
      • Operator to ensure storage areas are maintained clean and organized to facilitate the monitoring of pest control
      • Operator to ensure food premise shall be protected against the entry of pest
    • Floors clean and in good repair
      • * Fail to ensure floors of food premise are kept clean and/or in good repair
      • Operator to ensure floors are kept clean and in good repair
  3. Re-Inspection

    4 infractions

    • Equipment, non-food contact surfaces and linen are maintained, designed, constructed, installed and accessible for cleaning
      • * Fail to maintain all equipment/non-food contact surfaces are in clean and in good repair
      • Operator to ensure that all equipment/non-food contact surfaces are maintained clean and in good repair
    • Adequate protection against the entrance of insects, vermin, and rodents
      • * Fail to prevent the entrance of insect / rodent / pest
      • * Evidence of significant pests observed
      • Operator to ensure food premise shall be protected against the entry of pest
    • Floors clean and in good repair
      • * Fail to ensure floors of food premise are kept clean and/or in good repair
      • Operator to ensure floors are kept clean and in good repair
    • The premises is maintained free from every SERIOUS condition that may be a health hazard, adversely affecting the sanitary operation of the premises or adversely affecting the wholesomeness of the food
      • Observed significant insect/rodent infestation
      • Operator to operate and maintain premise free from every condition that may be a health hazard
  4. Routine

    8 infractions

    • Food is prepared in a safe manner
      • * Potentially hazardous foods observed at an internal temperature between 4° C (40°F) and 60°C (140°F) for greater than 2 hours
      • CCP monitoring should be conducted by operator
      • Operator to ensure potentially hazardous foods are prepared in a safe manner
    • Food protected from potential contamination and/or adulteration
      • * Fail to protect food from contamination and/or adulteration
      • Operator to ensure all food is properly stored, displayed, transported and served to prevent contamination
      • Operator to ensure all foods are stored off the floor
    • Proper storage of single-service containers/articles (utensils)
      • * Fail to protect single-service articles (utensils) from contamination
      • Operator to ensure single-service containers/articles are protected and stored in a manner to prevent contamination
    • Food contact surfaces properly designed, constructed, installed, maintained, located (smooth, non-absorbent, cleanable, corrosion resistant and non-toxic)
      • * Fail to maintain utensils, multi-service articles and/or food contact surfaces in a clean and sanitary manner and/or in good repair
      • Operator to ensure all food contact surfaces, utensils and/or multi-service articles are cleaned and sanitized after each use and are maintained in good repair
    • Equipment, non-food contact surfaces and linen are maintained, designed, constructed, installed and accessible for cleaning
      • * Fail to maintain all equipment/non-food contact surfaces as readily cleanable and non-absorbent
      • * Fail to maintain all equipment/non-food contact surfaces are in clean and in good repair
      • Operator to ensure that all equipment/non-food contact surfaces are maintained clean and in good repair
      • Operator to ensure that all equipment/non-food contact surfaces are readily cleanable/non-absorbent and of sound and tight construction.
    • Adequate protection against the entrance of insects, vermin, and rodents
      • * Fail to maintain premise free from every condition that may adversely affect the sanitary operation of the premise
      • * Fail to prevent the entrance of insect / rodent / pest
      • * Evidence of significant pests observed
      • Operator to ensure storage areas are maintained clean and organized to facilitate the monitoring of pest control
      • Operator to ensure food premise shall be protected against the entry of pest
    • Floors clean and in good repair
      • * Fail to ensure floors of food premise are kept clean and/or in good repair
      • * Fail to maintain floors free from clutter to permit adequate cleaning
      • Operator to ensure floors are kept clean and in good repair
      • Operator to ensure floors are maintained from clutter to permit adequate cleaning
    • General housekeeping is satisfactory
      • * Fail to remove all materials not associated with the daily operation of the food premise
      • Operator to remove all materials not associated with the daily operation of food premise
  5. Re-Inspection

    5 infractions

    • Mechanical dishwashing: Wash / rinse water clean, water temperature, timing cycles, sanitizer
      • * Fail to provide an easily readable thermometer for the dishwashing and sanitizing temperatures
      • Wash water must be between 60°C and 71°C
      • Operator to provide an easily readable thermometer to verify the dishwashing and sanitizing temperatures
    • Manual dishwashing: Wash, rinse, sanitize technique
      • * Fail to use proper wash/rinse/sanitize technique
      • Chlorine sanitizer concentration must be at least 100 parts per million and not lower than 24°C for at least 45 seconds
      • Operator to ensure the proper wash/rinse/sanitize dishwashing technique is applied
    • Food contact surfaces washed / rinsed / sanitized after each use and following any operations when contamination may have occurred
      • * Fail to wash, rinse and sanitize equipment / utensils after each use or as often as necessary
      • Operator to ensure all food contact surfaces are properly cleaned & sanitized
    • Floors clean and in good repair
      • * Fail to ensure floor of dishwashing area kept clean and in good repair
      • Operator to ensure floors are kept clean and in good repair
    • Exclusion of live animals on the premises, subject to exemptions
      • * Fail to ensure room kept free from live birds / animals
      • Operator to ensure premise is kept free from live birds / animals
  6. Routine

    9 infractions

    • Hand washing basin with supplies of hot and cold water, soap in a dispenser and single-use towels
      • * Fail to provide hot and cold water for hand washing in food preparation area
      • Operator to ensure hand washing basins are adequately supplied
    • Minimum of 1 Certified Food Handler per hour of operation?
      • * Fail to provide a minimum of 1 certified food handler per hour of operation
      • Operator to ensure a minimum of 1 certified food handler is present during every hour of operation
    • Food protected from potential contamination and/or adulteration
      • * Fail to protect food from contamination and/or adulteration
      • * Observed scoops/utensils not being stored in a sanitary manner to prevent contamination and/or adulteration
      • Operator to ensure all food is properly stored, displayed, transported and served to prevent contamination
      • Operator to ensure scoops/utensils are stored and maintained in a sanitary manner to prevent contamination and/or adulteration
    • Food contact surfaces properly designed, constructed, installed, maintained, located (smooth, non-absorbent, cleanable, corrosion resistant and non-toxic)
      • * Fail to use equipment/utensils/dishes/food containers/multi-service articles in good repair (i.e. free from cracks/crevices/chips/open seams)
      • Operator to ensure all food contact surfaces, utensils and/or multi-service articles are cleaned and sanitized after each use and are maintained in good repair
    • Food contact surfaces washed / rinsed / sanitized after each use and following any operations when contamination may have occurred
      • * Fail to wash, rinse and sanitize equipment / utensils after each use or as often as necessary
      • Operator to ensure all food contact surfaces are properly cleaned & sanitized
    • Sanitary maintenance of and provision of required supplies in staff / public washroom facilities
      • * Fail to equip facility with hot and cold running water
      • Operator to ensure the washroom facilities are properly supplied with soap/detergent, single-service towels or hot air dryer, toilet paper and hot and cold running water
    • Adequate protection against the entrance of insects, vermin, and rodents
      • * Evidence of pests observed
      • Operator to ensure food premise shall be protected against the entry of pest
    • General housekeeping is satisfactory
      • * Fail to remove all materials not associated with the daily operation of the food premise
      • Operator to remove all materials not associated with the daily operation of food premise
    • Exclusion of live animals on the premises, subject to exemptions
      • * Fail to ensure room kept free from live birds / animals
      • Operator to ensure premise is kept free from live birds / animals
  7. Routine

    3 infractions

    • Food protected from potential contamination and/or adulteration
      • * Observed scoops/utensils not being stored in a sanitary manner to prevent contamination and/or adulteration
      • Operator to ensure scoops/utensils are stored and maintained in a sanitary manner to prevent contamination and/or adulteration
    • Equipment, non-food contact surfaces and linen are maintained, designed, constructed, installed and accessible for cleaning
      • * Fail to maintain all equipment/non-food contact surfaces are in clean and in good repair
      • Operator to ensure that all equipment/non-food contact surfaces are maintained clean and in good repair
    • Adequate protection against the entrance of insects, vermin, and rodents
      • * Evidence of pests observed
      • Operator to ensure storage areas are maintained clean and organized to facilitate the monitoring of pest control
      • Operator to ensure food premise shall be protected against the entry of pest
  8. Routine

    2 infractions

    • Potentially hazardous food is held at 4°C (40°F) or lower
      • * Fail to ensure potentially hazardous foods are held at 4°C (40°F) or less
      • CCP monitoring should be conducted by operator
      • Potentially hazardous foods observed at an internal temperature above 4° C (40°F)
      • Operator to conduct internal temperature checks of potentially hazardous foods
      • Operator to ensure potentially hazardous foods are held at 4°C (40°F) or lower
    • Equipment, non-food contact surfaces and linen are maintained, designed, constructed, installed and accessible for cleaning
      • * Fail to maintain all equipment/non-food contact surfaces are in clean and in good repair
      • * Fail to ensure filters in the ventilation system are maintained in a clean and sanitary manner
      • Operator to adjust or repair the malfunctioning cooler immediately. Do not store any potentially hazardous foods in the malfunctioning unit until it is able to maintain hazardous foods at 4° C or lower
      • Operator to ensure that all equipment/non-food contact surfaces are maintained clean and in good repair
      • Operator to ensure filters in the ventilation system are maintained in a clean and sanitary manner
  9. Routine

    3 infractions

    • Food protected from potential contamination and/or adulteration
      • * Observed scoops/utensils not being stored in a sanitary manner to prevent contamination and/or adulteration
      • Operator to ensure scoops/utensils are stored and maintained in a sanitary manner to prevent contamination and/or adulteration
    • Equipment, non-food contact surfaces and linen are maintained, designed, constructed, installed and accessible for cleaning
      • * Fail to maintain all equipment/non-food contact surfaces are in clean and in good repair
      • Operator to ensure that all equipment/non-food contact surfaces are maintained clean and in good repair
    • Floors clean and in good repair
      • * Fail to ensure floor of food-handling room kept clean and in good repair
      • Operator to ensure floors are kept clean and in good repair
  10. Re-Inspection

    1 infraction

    • Food protected from potential contamination and/or adulteration
      • * Observed scoops/utensils not being stored in a sanitary manner to prevent contamination and/or adulteration
      • Operator to ensure scoops/utensils are stored and maintained in a sanitary manner to prevent contamination and/or adulteration
  11. Routine

    5 infractions

    • Potentially hazardous food is held at 4°C (40°F) or lower
      • * Fail to ensure potentially hazardous foods are held at 4°C (40°F) or less
      • CCP monitoring should be conducted by operator
      • Potentially hazardous foods observed at an internal temperature above 4° C (40°F)
      • Operator to conduct internal temperature checks of potentially hazardous foods
      • Operator to ensure potentially hazardous foods are held at 4°C (40°F) or lower
    • Food protected from potential contamination and/or adulteration
      • * Fail to protect food from contamination and/or adulteration
      • * Observed potentially hazardous food not covered to prevent contamination / adulteration
      • * Observed scoops/utensils not being stored in a sanitary manner to prevent contamination and/or adulteration
      • Operator to ensure all food is properly stored, displayed, transported and served to prevent contamination
      • Operator to ensure scoops/utensils are stored and maintained in a sanitary manner to prevent contamination and/or adulteration
      • Operator to ensure all foods are covered in storage
    • Equipment, non-food contact surfaces and linen are maintained, designed, constructed, installed and accessible for cleaning
      • * Fail to maintain all equipment/non-food contact surfaces are in clean and in good repair
      • * Fail to ensure filters in the ventilation system are maintained in a clean and sanitary manner
      • Operator to adjust or repair the malfunctioning cooler immediately. Do not store any potentially hazardous foods in the malfunctioning unit until it is able to maintain hazardous foods at 4° C or lower
      • Operator to ensure that all equipment/non-food contact surfaces are maintained clean and in good repair
      • Operator to ensure filters in the ventilation system are maintained in a clean and sanitary manner
    • Adequate protection against the entrance of insects, vermin, and rodents
      • * Fail to maintain premise free from every condition that may adversely affect the food therein
      • * Evidence of pests observed
      • Operator to ensure food premise shall be protected against the entry of pest
    • Walls clean and in good repair
      • * Fail to ensure walls of food premise kept clean and in good repair
      • Operator to ensure walls of food premise are maintained in a sanitary condition and in good repair

Nearby inspected facilities

Own this business? Add a badge to your website